This article gives you a talk about the heat plate making wireless charging, as well as the heat plate installation video corresponding knowledge points, I hope to help you, do not forget to collect the site oh. < / p > < h2 > the article directory list: < / h2 > < ul > < li style = 'margin - bottom: 3 px; list-style: none'>1, kalar wireless thermostatic bowl how to change the battery
1, no need to change the battery, direct chargeElectricity will do. A thermostatic bowl, also known as a thermal bowl, is a tableware that keeps food at the desired temperature. The thermostatic bowl is composed of electric heating plate, bowl holder, stainless steel small bowl, sealed bowl cover and insulation cover. The thermostatic bowl is mainly for children from 6 months to 3 years old, and can also be used for the elderly or sick.
2, wave cuck smart constant temperature bowl battery replacement method is as follows. First of all, turn off the power to the Bockers smart thermostatic bowl. Secondly, the bottom faces upward, and the bottom adopts rubber pad design. Unscrew the rubber pad to replace the battery of the smart thermostatic bowl.
3, replace the battery of the temperature display of the thermos cup, usually by opening
1, ①, about the above induction cooker heating plate line is not long enough, it can not be connected with a wire, the reason is that if the wire is long, it will increase the inductance of the heating coil, which is unfavorable to the heating resonance circuit.
2, induction cooker wire tray copper resistance is small, at the same time the anti-aging strength is good, heating is also small, faster, you can use the same specification of round copper high-strength enamelled wire to replace aluminum enamelled wire, pay attention to the diameter of a single wire, the number of parallel roots, and finally soak with insulation varnish drying.
3, induction cooker wire tray is a coil, wound with copper wire. Connection of induction cooker wire reelMethod: Starting from the outer ring, connect the IGBT to the outer ring of the winding clockwise, and connect the inner ring to 300V. Starting from the outer ring, press the outer ring of the counterclockwise winding to connect 300V, and the inner ring to connect IGBT.
2, the four catch lines of the commercial rice cooker are two disks, and the two disks can be connected in parallel. The four connecting column lines of the electronic temperature control type rice cooker are: a pin for each disc, a separate wire to the control board, and the other two are connected in parallel. The four column lines of the rice cooker with multi-level insulation type are: the two disks are connected in parallel, and the heating disk of the outer ring is connected in a series of heat preservation.
3, the smart rice cooker is mainly composed of a power supply part and a control circuit, and the main control circuit forms a feedback with the thermistorLoop, the main control circuit to achieve two functions, one is to collect the temperature value of the thermistor feedback, the other is to control the heating of the electric heating plate according to the working mode selected by the user and the change of the working mode of the relay.
4, the heating plate of the rice cooker is 220v electricity, when the heating wire of the heating plate is open, the multimeter is used to measure the voltage at both ends of the heating wire is 220v, if the heating wire is normal, then it can not measure the voltage when working, because its two ends are equal potential.
5, the rice cooker does not work, may be due to the following reasons. This article will introduce youRice cooker does not work causes and solutions. Deformation of the inner pot or thermostat failure The inner pot deformation or thermostat failure will lead to poor temperature of the rice cooker, the rice is not good, the inner pot has sensed high temperature, the thermostat automatically cut off the heat. Solution: Replace the inner pan or thermostat.
6, the rice cooker has a temperature control device to regulate the temperature of the heating plate, generally by the temperature limit and thermostat two parts. Temperature limiting device: The heating plate will not exceed 103±2 ° C during cooking, and is installed in the center cavity of the heating plate. Thermostat: stable at 60 ~ 80℃ during heat preservation, installed under the heating plate or other appropriate locations.
If your rice cooker is close to the water source, it is easy for the water to splash onto the power cord when in use, which will easily lead to leakage of the rice cooker. Solution: The problem is that the power of the rice cooker should be turned off first, and the place with water should be wiped clean using a dry towel or paper towel, and then the power can be turned on. So as toSafe. Run it again with a pencil, see if there's still a leak.
The heating principle of the heating plate of the rice cooker is to generate heat by passing an electric current through a conductive substance (usually a metal). When an electric current flows through a conductive substance, it produces a molar thermal effect, that is, when an electric current passes through a conductive substance, it heats the substance. This heat is transferred to the food, causing it to heat up and cook.
Rice cooker varieties are also many, need to be opened to know, the old-fashioned rice cooker heating is connected to the power supply by the magnet, the spring switch linkage mechanism, put the inner tank, press the switch button, the magnet is drawn, in order to maintain the power, such asIf it is not subject to the above control, it is broken, need to be disassembled, in order to find out the cause of the fault, generally they can be repaired. If you do not understand the principle, you can learn online to find the cause of the failure.
Aging The heating plate of the rice cooker is mainly made of metal, and aging and oxidation will occur during long-term use, resulting in leakage of electricity in the heating plate of the rice cooker. If the heat plate aging caused by leakage, need to replace the heat plate in time. Loose socket Sometimes the socket of the rice cooker is not tightly connected to the power supply, which is prone to leakage.
First of allThe structure of ordinary rice cooker: ordinary rice cooker is mainly composed of heating plate, temperature limiting device, heat preservation switch, lever switch, current limiting resistor, indicator light, socket and so on. The working principle of the rice cooker is as follows: heating plate This is the main heating element of the rice cooker. This is an aluminum alloy disc embedded with electric heating tube, the inner pot is placed on it, take off the inner pot can be seen. Temperature limiter is also called magnetic steel.
Heating plate: This is the main heating element of the rice cooker. This is an aluminum alloy disc embedded with electric heating tube, the inner pot is placed on it, take off the inner pot can be seen. Temperature limiter: also called magnetic steel. It's built insideA permanent magnetic ring and a spring, which can be pressed, are located in the center of the heating disc.
Heating plate production wireless charging introduction to talk here, thank you for taking the time to read the content of the site, more about the heating plate installation video, heating plate production of wireless charging information don't forget to find in the site.