When charging, push the plug out completely and plug it directlyEnter the AC110V~240V/50~60Hz power socket, the corresponding charging indicator light, full power needs about 14 hours. When in use, press the switch button for low light lighting, press the second button for strong light, and press the third button to turn off the light.
Charge the LED charging desk lamp when the power is running out, can not run out of power, and then charge, please stay in the small amount of electricity and then charge. If it is not used for a long time, it can be charged once in a while, and it must be kept in a wet place on the ground. If you need to replace the light source (light tube), be sure to refer to LThe specified parameters of the ED charging lamp are assembled, and do not change the structure.
Rough judgment: After two hours, try to light the lamp every half hour to observe (do not fill while bright), add the result of the light is the brightest and the lamp brightness should no longer increase, and then float the same charging time can be adopted.
1, usb desk lamp with the charger plugged in the socket for plugging, the charger is a step-down device, you can convert the household power supply into a suitable power supply and current for charging. usb stationThe lamp is mainly used in the USB interface of the desktop computer or laptop micro-charging desk lamp, of course, there are also outlet direct charging portable desk lamps.
2, therefore, you can directly charge, do not worry about overcharge or loss of power. The first charge The first charge takes 4-6 hours, and when you feel the brightness decreases, you can charge it in time. With the right way of charging, you can eliminate the memory effect and make the lamp's brightness last as long as new.
3, when charging, the lamp AC plug is completely pushed out, directly inserted into the AC90 to 240V power socketThe corresponding charging finger lights up, indicating that the lamp is in a charging state and has sufficient power for about 12 hours. When in use, push the switch button, the first gear is 9 LED weak light, the second gear is 15 LED strong light, and the top gear is turned off the light. Fully charged, the first gear can be used continuously for about 10 hours, and the second gear can be used continuously for about 5 hours.
4, the external power supply selection switch, when "5V", for charging, when "DC", for external DC power supply. The details are as follows: "5V" : charging gear, allowing charging while using. Comes with a USB power adapter, or use your computer's USB10V~240V/50~60Hz power socket, the corresponding charging indicator light, sufficient power takes about 14 hours. When in use, press the switch button for low light lighting, press the second button for strong light, and press the third button to turn off the light.
2, the use method is as follows: After plugging in the power supply, touch the curved light pole with your finger at any position to light the light. Put the device that needs to be charged under the lamp, switch the mobile phone to the wireless charging mode, and put it into the wireless charging induction area of the lamp. Use the phone charging cable to connect the lamp USB port to the phone, and the phone can also be charged.
3, rough judgment:After charging for two hours, try to light the lamp every half hour to observe (do not fill while lighting), and if the indicator light is the brightest and the lamp brightness no longer increases, it should be full, and then float the same charging time can be adopted.
4, the external power supply selection switch, when "5V", for charging, when "DC", for external DC power supply. The details are as follows: "5V" : charging gear, allowing charging while using. Comes with a USB power adapter, or charge with your computer's USB port. DC: It is used for external DC power supply and cannot be charged. Can be connected to external mobile charging bank, battery, etc.
5, check whether the power socket is powered on, replace the power socket test, after the power on the adapter indicator light green. Check that the adapter is properly connected to the power cord. Remove the filter element assembly, restart the power switch, and finally push it to start the machine. After the Qinbao is fully connected with the charging stand, long charge 4-5 hours before use observation. The white light of the power indicator of the body when charging is blinking. After full charge, it is steady on first and then off.
6, open the folding desk lamp, turn on the power button to illuminate the learning. Plug the two ends of the lamp power cord completely into the AC socket of the lamp, and plug the end with the plug directly into the AC9On the 0V~240V power socket, the corresponding charging indicator lights up, indicating that the lamp is in the charging state, charging for about 10 hours.
Plug in 220V AC and you're done. Rechargeable light bulbs usually charge for four hours to full. Do not keep charging after full, because this will overload the battery, it is easy to break. For a long time, the battery will become less durable, and safety is not guaranteed.
Fully insert one end of the two holes of the lamp power cord into the AC socket of the lamp, and directly insert the end with the plug into the AC90V~240V power socket. The corresponding charging indicator is on, indicating that the lamp is in the state of charging, and the charge is about 10For an hour. Student dormitory artifact bedroom lamp folding portable creative learning eye protection lamp ultra-long life reading light, for you to find student dormitory artifact bedroom lamp folding portable creative learning eye protection lamp ultra-long life reading light reading light.
Wireless charging table lamp how to charge the introduction to talk about it here, thank you for taking the time to read the content of the site, more about wireless charging table lamp how to charge video tutorials, wireless charging table lamp how to charge information don't forget to find in the site.