Today to share the knowledge of the mobile phone wireless charging port can not be charged, which will also explain the mobile phone wireless charging, if you happen to solve the problem you are now facing, don't forget to pay attention to the site, start now!
< ul>The phone case is too thick will affect the phone's internal charging coil and wireless chargingDevice induction, resulting in failure to charge normally. Therefore, it is recommended to remove the protective case of the mobile phone before using the wireless charger to charge; The charging coil area in the mobile phone is small, and if the mobile phone is placed incorrectly when wireless charging is used, it will also lead to normal charging.
Cause: The system program has a problem, resulting in abnormal charging function hardware, it is recommended to restore the phone to normal use. The reason why the short circuit causes the Apple mobile phone to be charged is likely to be caused by the short circuit of the charging interface. There are a large number of spring firing pins in the charging interface of the mobile phone. These firing pins can make the line and the plug of the charging data line closely connected in oneIt is recommended that you remove the phone protective case and try again. 4, please check whether there are other items between the mobile phone and the wireless charger. Wireless charging converts electrical energy into magnetic energy for transmission to the phone, and if the magnetic energy is interfered with, charging will be affected.
2, check whether the phone is overheating, it is recommended to charge in a good heat dissipation environment. Check whether the wireless charger indicator light is on normally, and check whether the connection between the charging base, data cable, charger, and power supply is in poor contact. It is recommended to reinsert the wireless charger. Check whether the center position of the mobile phone is placed in the center of the wireless charging base during charging, and remove the device and noneOther items between line chargers (such as bus cards, metal and other substances).
3, when there is inclusions between the mobile phone and the wireless charging board, it may not be able to charge normally. Please check the back of the phone. If the protective phone cover used is too thick may hinder wireless charging, it is recommended to remove the phone cover and try to recharge. Please use the original charger. If you use a non-original charger, you may not be able to charge normally. Connect your phone directly to the wired charger to see if it can be charged.
4. The reasons are as follows: Click the button in the notification bar to enable wireless backcharging. The charged device needs to be placed inRight in the center of the back cover. The device to be charged needs to support the standard Qi wireless charging protocol (for example, AppleWatch is a non-Qi wireless charging device, which cannot be charged through the wireless backcharging function). There should be no metal ornaments or foreign objects between the phone and the device being charged.
5, cause: The system program has a problem, resulting in the charging function of the hardware is not normal, it is recommended to restore the phone can be used normally.
6. The power supply is faulty. If the battery of the charger is too low or the machine fails, you can connect the charger to the power supply and charge it again. touchBad. If the charging device is in poor contact with the charging base or the interface is dirty, use a soft cloth to clean the metal contact points on the charger and charging device. The power supply does not match. If the charger and the power supply do not match, it will lead to insufficient power and cannot be charged normally.
Poor contact. Check whether the charging interface at the bottom of the phone is in good contact with the data cable, if the contact is not good, it will not be able to charge. Replace the power cable or data cable. Sometimes the problem is with the power or data cableYou can try to replace the power cord or data cable respectively to eliminate the cause of the fault. The temperature is too low. Extreme low temperature environment will affect the normal use of wireless charging function.
Red rice k60 can not wireless charging solution: poor contact may be the bottom of the phone charging data cable is not connected, resulting in no charging, poor contact. Replacing the power cord or data cable may be one of the reasons, we can replace it respectively to see what the problem is. Turning off and on May also be the problem of the phone itself, and shutting down can solve most of the problems.
Red rice k60 supreme wireless charging can not be used: The phone is not placed correctly, the charger is faulty and other reasons. The phone is not placed correctly: Wireless charging requires close contact between the phone and the charger, and if the phone is not placed correctly, it cannot be charged. Charger failure: The charger itself has a fault, it can not charge normally.
Open the Redmi K60 phone, find the Settings app from the home screen or app list and tap Open. In the Settings screen, you'll need to find an option similar to Battery and charging or Wireless and networking, the name of which may vary depending on the phone's system version or region.
Using Red rice K60For wireless charging, you first need to ensure that the phone is properly connected to the wireless charger. Place the phone flat on the turned on wireless charger to start charging. To enable wireless charging on the Redmi K60, follow these steps: Go to your phone's Settings menu, find and tap the "Wireless Charging" option, and make sure it is turned on. Then, make sure the charger bank is fully charged and place the Redrice K60 on the wireless charger.
If you still can't charge using wireless charging, then you can try to replace the charging interface. Wireless charging technology has been widely used by many flagship mobile phones in recent years, and the corresponding wireless charging equipment is also very rich, and wireless charging technology has been relatively mature, there is no need to worry about the unknown impact of charging equipment on mobile phones. If the problem still cannot be solved after replacement, it is recommended to go to the after-sales service for maintenance.
Try to replace another wireless charging base to charge the phone and determine whether the fault is the fault of the mobile phone or the wireless charger. The non-Huawei wireless charger may be incompatible with the mobile phone, resulting in the wireless charging functionIf no, use a Huawei official wireless charger.
Because some mobile phone protective case is too thick, or the material of the mobile phone protective case may affect the recognition function of the mobile phone wireless charger, it is recommended that you remove the mobile phone protective case and try again. 4, please check whether there are other items between the mobile phone and the wireless charger. Wireless charging converts electrical energy into magnetic energy for transmission to the phone, and if the magnetic energy is interfered with, charging will be affected.
Hello, please charge the phone with the screen facing up in the center position of the charger or the position suggested by the charger manufacturer.
Please take off the mobile phone protective cover before charging because some mobile phone protective cover is too thick, or the material of the mobile phone protective cover may affect the recognition function of the mobile phone wireless charger, it is recommended that you take off the mobile phone protective cover and try again. 4, please check whether there are other items between the mobile phone and the wireless charger. Wireless charging converts electrical energy into magnetic energy for transmission to the phone, and if the magnetic energy is interfered with, charging will be affected.
Check whether the phone is overheated. It is recommended that the heat dissipation condition is goodAmbient charging. Check whether the wireless charger indicator light is on normally, and check whether the connection between the charging base, data cable, charger, and power supply is in poor contact. It is recommended to reinsert the wireless charger. Verify that the center of the phone is placed in the center of the wireless charging base during charging, and remove other items (such as bus passes, metals, etc.) between the device and the wireless charger.
Please check the connection of the wireless charger Please check whether the connection between the charger, data cable and wireless charger is normal; Whether there are other items between the mobile phone and the wireless charger, such as mobile phone protective cases, metal foreign bodies, etc.; handWhether the machine center is aligned with the center of the wireless charger base; Whether the wireless indicator light is on.
Please use the original protective case, do not use too thick or magnetic insulation material/metal material protective case, these protective cases may affect the charging efficiency or can not be charged, or even overheating to cause the phone can not be charged or damaged. If the above methods do not solve the problem, please back up the mobile phone data in advance, and bring the mobile phone, wireless charger, wired charger set and purchase voucher to vivo customer service center for testing.
The introduction of mobile phone wireless charging port and mobile phone wireless charging is over.Did you find the information you needed? If you want to know more about this, remember to follow this site. < / p >