This article gives you a talk about wireless charging and plugging, and wireless charging and plugging and plugging, how to charge the corresponding knowledge points, I hope to help you, don't forget to collect this site. < / p > < h2 > the article directory list: < / h2 > < ul > < li style = 'margin - bottom: 3 px; list-style: none'>1, How can wireless charging not charge?
During the charging process, please place the center of the mobile phone slightly lower in the center of the wireless charger base to avoid shifting the mobile phone. If the position deviation is large, it will not be able to charge. 6, please check whether the wired charging device is connected at the same timeWith wired charging and wireless charging, wired charging will be preferred.
If your mobile phone cannot use wireless charging, please follow the following steps: Check whether the mobile phone is overheating, it is recommended to charge in a good heat dissipation environment. Check whether the wireless charger indicator light is on normally, and check whether the connection between the charging base, data cable, charger, and power supply is in poor contact. It is recommended to reinsert the wireless charger.
Replace the wireless charger: When our mobile phone has such a situation, it is likely that we have a problem with the charger, at this time we can replace a wireless charger to try (originalInstall wireless charger or usb data cable) Restore factory Settings: if the fault is still on after the boot, we can try to restore factory Settings on the phone at this time.
The reason why the triple can not activate the fast charge may be several aspects. First, it may be that the charger itself does not support the fast charge function. Although some chargers have multiple interfaces, they do not necessarily support the fast charge function, so they cannot be activated when in use. Second, it may be the charging port of the phone or deviceThe port does not match the charger.
Battery aging: When the charging treasure is used for a long time, the battery aging results in reduced capacity and cannot be fully charged. (2) Outlet failure: The power bank outlet is damaged or poorly connected, resulting in unstable output current. (3) Input port failure: The charging bank input port is damaged or poorly connected, resulting in unstable charging current. (4) Charging power supply failure: The charging power supply failure of the charging treasure may cause the charging current to be unstable or unable to charge.
Many users may not be able to charge their mobile phones when they use the wireless charging function for the first timeThe reason for this can be that the phone is placed on the charging pad incorrectly or the charging device is not powered up. First confirm whether the mobile phone model supports wireless charging function, (you can find the mobile phone information on the brand's official website) Check whether the indicator light of the charging board is on.
Internal fault, current exceeds the standard. Internal failure: There is a fault in the charger internal circuit, such as thermistor damage or circuit board short circuit, etc., turn off the charger, stop using it for a period of time, and let the charger cool naturally. Excessive current: The voltage or current used by the charger exceeds its rated range,If it causes the charger to overheat, check the operating instructions of the charger to confirm whether the voltage and current used by the charger are within the rated range.
The reasons are as follows: The data cable is in poor contact, it is recommended to use a new cable or use the original data cable. The output current is too small, you can use the 2A adapter to charge the power bank. The power supply of the charging treasure is excessive, resulting in no charging, with both ends of the usb port of the line, one end of the power supply outlet, one end of the computer u port for one to three minutes, you can activate. Check the ports, circuit boards, and batteries of the charging bank.
May be out of power, the protection state is blinking. 20W millet wireless charger packaging or the past millet has always been simple white packaging, the front of the package in addition to the appearance of a wireless charge, there is no other introduction. There is almost no content in the package, only the name of the product on the side of the package: Millet wireless charger.
Can be out of power, the protection status is blinking. When the millet wireless charger, millet wireless charger (universal fast charger) LED light status is green flashingXiaomi wireless charger is in the error and protection stage. At this time, you should pay attention to whether there is a metal object placed on the wireless charger, please remove it and charge it again. The power will be off for a while, this is not placed in the right position, detected metal foreign objects, automatic protection Settings.
When many users use the mobile phone wireless charging function for the first time, the mobile phone may not be charged, generally, the reason for this situation may be that the mobile phone is placed in the incorrect position on the charging board or the charging device is not powered on. Wireless charger does not charge how to first confirm whether the mobile phone model supports wireless charging function, (can be inThe introduction to talk about it here, thank you for taking the time to read the content of the site, more about wireless charging, wireless charging information do not forget to find oh in the site.