1, you can buy a wireless charging receiver, stick it on the back of the phone or insert the phone charging port, the advantage of this method is that the cost is low, no needThe disadvantage of replacing the mobile phone or disassembling the inside of the mobile phone is that it may affect the beauty and feel of the mobile phone, as well as increase the wear of the charging port.
2, the self-made mobile phone wireless charging method is as follows: Prepare materials: The mobile phone charger first cut the USB charging cable into two sections not far from the two ports. Use scissors to separate the tail glue of the two wires into a section to screen and then cut off the green wire with a double bottom line. Use hot glue to attach the magnet to the charger. Wrap the wires in the USB with tinfoil. Then wrap the wires and roll them up with copper wire.
3, to add the wireless charging function to the ordinary mobile phoneOn top of that, the most critical thing is to install a wireless charging receiver. This process usually involves opening the case of the phone, finding where the battery or battery is connected, and welding or connecting the receiver to the appropriate circuit. This requires a certain amount of electronic knowledge and fine manual skills, because the components inside the phone are very small and fragile.
4, wireless charger usage: the mobile phone standard charger and data cable connected to the wireless charger, and then the mobile phone is/horizontally placed in the wireless charger base left and right center position, you can achieve wireless charging, the indicator light will have a breathing effect, 5 seconds after the extinguish, plug and play, convenient and quick.
5, question 1: How to make wireless charger? There are many ways to use wireless chargers, mainly to see how the reception is installed. But no matter what the product is close, the operation method is placed on the launch plate. Take the mobile phone for example, the current mobile phone is generally added a mobile phone jacket, in this jacket there is a wireless receiver module. The phone can be charged wirelessly with this jacket.
6. First, make sure your phone supports wireless charging. Connect the wireless charging pad and charging head through the data cable. Generally, you only need to ensure that it is above 10W. Leave your phone chargingOn the board, the coil is usually located near the camera. There will be a prompt after charging successfully. If your Huawei mobile phone supports wireless charging, after the wireless charger is powered, directly place the mobile phone screen facing up in the center of the charger or the position suggested by the manufacturer to charge it.
An iPhone wireless charging receiver card. A compatible charger. A non-metal flexible ultra-thin casing.
First, you need to prepare the following simple tools: iPhone wireless charging receiver card: This is a key component to achieve wireless charging, and can be purchased on platforms such as Taobao for tens of yuan.A compatible charger: Make sure it matches your iPhone model to provide a stable charging experience. Non-metal flexible ultra-thin case: In order to protect your phone and receiving card, it is wise to choose a thin and light case.
You can buy a wireless charging receiver, stick it on the back of the mobile phone or insert it into the mobile phone charging port, the advantage of this method is that the cost is low, there is no need to replace the mobile phone or disassemble the internal phone, the disadvantage is that it may affect the beauty and feel of the mobile phone, as well as increase chargingAbrasion of the mouth.
First cut the USB charging cable into two sections not far from the two ports. Use scissors to separate the tail glue of the two wires into a section to screen and then cut off the green wire with a double bottom line. Use hot glue to attach the magnet to the charger. Wrap the wires in the USB with tinfoil. Then wrap the wires and roll them up with copper wire. The USB cable with the copper wire rolled up is then wrapped in electrical tape.
To add wireless charging function to ordinary mobile phones, the most critical is to install a wireless charging receiver. This process usually involves opening the case of the phone and finding the battery or electricityThe pool is connected to the location and the receiver is welded or connected to the corresponding circuit. This requires a certain amount of electronic knowledge and fine manual skills, because the components inside the phone are very small and fragile.
Vertically place the mobile phone on the wireless charger to charge: Please first place the wireless charging pad on the tray of the wireless charger, increase the tray height, and then place the mobile phone on the wireless charger to charge; Horizontal charging of the mobile phone on the wireless charger: The mobile phone can be directly placed on the wireless charger to charge without placing the wireless charging pad. If the wireless charging pad has been placed before, please remove it first and then charge it horizontally.
Question 1: How to make wireless charger? There are many ways to use wireless chargers, mainly to see how the reception is installed. But no matter what the product is close, the operation method is placed on the launch plate. Take the mobile phone for example, the current mobile phone is generally added a mobile phone jacket, in this jacket there is a wireless receiver module. The phone can be charged wirelessly with this jacket.
First, make sure your phone supports wireless charging. Connect the wireless charging pad and charging head through the data cable. Generally, you only need to ensure that it is above 10W. Put the phone on the charging pad, wireThe circle is usually located near the camera. There will be a prompt after charging successfully. If your Huawei mobile phone supports wireless charging, after the wireless charger is powered, directly place the mobile phone screen facing up in the center of the charger or the position suggested by the manufacturer to charge it.
1, an iPhone wireless charging receiver card. Wireless charging receiving card a compatible charger. A non-metal flexible ultra-thin casing.
2, the method of making a wireless charger is as follows: Attach the module to the MicroUSB interface comparison. Connect the MicroUSB or Lightning port on the module to your phone. If there is double-sided tape on the receiver, you can glue it directly to the back of the phone. If it doesn't come with it, you have to figure it out yourself. Choose the most suitable position, be careful not to let the part of the connection line have the phenomenon of warping.
3, the sending end coil is connected to the wired power supply to generate electromagnetic signal, and the receiving end coil senses the electromagnetic signal of the sending end to generate current to charge the battery. Materials and tools: Wireless Charger kit: charger, charging base, charging cable,Transmitter and receiver. iPhone6 Wireless Charging kit: reed tube, wired tail plug, iPhone6 back cover, iPhone6 back cover glass. Installation is very simple, straight above.
4, one of the self-wound coil connected in the charging circuit, 555 output foot (third foot) with an output tube (at your own will, but to high frequency power tube) output tube link self-wound coil, will be connected to the two coils close (about 1 cm or so there is a very sufficient charging current) power can be wireless charged! This circuit is very inefficient, because only half a wave crest is high frequencyThe loss is relatively large, but the principle is quite simple and easy to make.
5, no magnet in the wireless charger. If you place an energized wire on a magnetic compass, you can see that these currents also produce a magnetic field. If you use a moving magnet instead of an alternating current wire, you're ready. The varying currents in the wires create varying magnetic fields. The changing magnetic field creates an electric current in the other coil. The more loops you create, the stronger the effect.
1. First you need these things: an iPhone's wireless charging card. A compatible charger. A non-metal flexible ultra-thin casing.
2, first of all, you need to prepare the following simple tools: iPhone wireless charging receiving card: This is the key component to achieve wireless charging, can be purchased in Taobao and other platforms for tens of yuan. A compatible charger: Make sure it matches your iPhone model to provide a stable charging experience. Non-metal flexible ultra-thin case: to protect the phoneAnd receiving cards, it is wise to choose a thin and light case.
3. iPhone wireless charging receiving card. A compatible charger. A piece of non-metal flexible ultra-thin shell these gadgets can be purchased by the universal X Treasure search, and the general price is dozens of yuan, as shown in the following figure.
4, [iPhone6 Wireless charging tutorial] Prepare materials and tools: wireless charger kit: charger, charging base, charging cable, transmitter and receiver. IPhone 6 Wireless charging kit: reed tube, wired tail plug, iPhone6 back cover, iPhThe one6 back cover glass is actually very simple to install and operate, and the following Xiaobian directly uses three pictures to illustrate.
5, Prepare tools: iPhone wireless charging receiver. A compatible charger. A non-metal flexible ultra-thin shell DIY iPhone 7 support wireless charger is very simple, just need to plug the wireless charging card into the data interface, and then fold it into the back cover of the phone or hidden in the protective case, and then find an iPhone wireless charging receiver set up on the line.
6, just said, wireless charging is sold by the user body