Today to share the knowledge of wireless charging how to connect the circuit board, which will also explain the wireless charger circuit diagram, if you happen to solve the problem you are now facing, don't forget to pay attention to the site, now start!
< ul>1, the mobile phone charger 5 lines with 2 lines charging, only need to put the red and black lines in the 5 lines, according to the color of the different connection to 2Line can; To connect 4-wire charging, you need to connect the red, black, green and white lines in the 5 lines to the 4 lines respectively according to different colors. The two connections are shown below. 5-wire connection 2-wire charging connection. 5-wire connection 4-wire charging connection.
2, first follow the positive and negative poles and color matching from left to right. Followed by the English letters V, D-, D, G. Finally, the color of the Apple 5 data cable is red, black, green, white, V is connected to the positive electrode (red line), G is connected to the negative electrode (black line), D- is connected to the white line, D is connected to the green line, and you can stick it with tape.
3, red to red, black to black, and then the two signalsLine shorting. The iPhone is different from other mobile phones in that it has a chip in the charging head for authentication.
4, respectively connected to the four lines according to the color. It is only necessary to connect the red and black lines in the 5 lines to the 4 lines respectively according to the different colors, the method is red to red, black to black, and then short connect the two signal lines.
5, cut the insulation skin of the head of the 5 wires about 1cm, exposing the copper wire. Take two of the wires and twine them together. Wrap the third wire copper wire around the left side of the first two connectors. The fourth is in the middle and the fifth is on the right. With another copper wire, will connectOpen the socket: Use a screwdriver to open the wireless socket and plug. Then, remove the buckle and wiring terminals. Remove the buckle and orange wiring terminals and prepare to connect cables. Next, connect the wires: connect the red wire to the L pole, the blue wire to the N pole, and connect the yellow and green wire to the E pole.
Problem 1: How to wire the bull wireless socket The cover plate behind the socket is unscrewed, the three heads of the wire are peeled off the insulation layer, the wire head is connected to the copper connector inside the socket with a cross, and then the cover cover is ok.
All sockets (not just bull plugsThe wiring should use red, blue, yellow and green three kinds of lines, of which: the red line is the fire line, the blue line is the neutral line, and the yellow-green two-color line is the ground line, which is easy to install and easy to maintain. The red line is connected to the socket L terminal, the blue line is connected to the socket N terminal, and the yellow and green line is connected to the socket E (or there is a vertical three horizontal symbols in the circle) terminal.
Such a strip is the kind of soft wire that should be connected with a lot of fine copper wire: if there are conditions, the wire head to be connected is plated with some solder, if there are no conditions, the wire head is folded once or twice, and then tighten, and then screw to the black terminal post.
First of all, a good screwdriver, three-hole wireless converter socket, plug, wire, and then the coat of the power cord is removed, exposing the copper wire inside, and then the wireless socket and plug with a screwdriver to open, unscrew the buckle and orange terminal ready to connect. First screw on the power cord, the red is connected to the L pole, the blue is connected to the N pole, and the yellow and green are connected to the E pole.
The bull socket connection diagram is as follows: When wiring, connect the red wire (live wire) and blue wire (neutral wire) to the L and N terminals respectively, connect the yellow and green two-color wires to the N terminal, and then connect the L terminal and the switch end with the broken wireThe sub is then connected to the switch terminal L using the other connection of the bulb.
How to wire the wireless socket how to wire the wireless socket to prepare the required materials and tools (wireless board, plug, wire, screwdriver), the quality of these materials can be better, the wire according to their needs to buy size. How to connect the wireless socket first connect the plug. Remove the wire from the two wires, remove the plug cover with a screwdriver, then loosen the wire screws on the metal piece of the plug.
If you want to wire the bull wireless socket, you should first remove the outer cover of the wire a little, so that the copper core inside can be exposed. Next should use a screwdriver to put the bull withoutUnscrew the cable socket and take the socket and plug apart. Next, you should unscrew the buckle of the bull wireless socket, and also unscrew the orange terminal, and then you are ready to start wiring.
There are many kinds of wireless sockets, you can see on many shopping websites. In fact, wireless means that there is no excess power cord to show, which will make your desktop or the environment more tidy and clean. First open the back cover of the socket with a screwdriver. Connect cables according to the mark. L is the live line and N is the neutral line. And a ground wire. Secure the power cord with screws. Secure the power cable with a crimping bar.
Socket in our lives play a very important seat, with the development of science and technology, now the wireless power socket into the market, generally open, find the terminal, marked with L is the front line, marked with N is the neutral line, marked with E is the ground line, the corresponding wire connection after the shell can be installed. If the socket will not pick up, it is recommended to go to the electrician indirectly, do not recommend DIY.
There are many kinds of wireless sockets, and different families can choose the appropriate size wireless socket according to the actual needs. We usually wire our own wireless outlets at home. First prepare the appropriate items, such as MeiA screwdriver, a three-hole wireless converter socket, a plug, a length of suitable wire.
1, wireless charger usage: the mobile phone standard charger and data cable connected to the wireless charger, and then the mobile phone is placed (vertical) or horizontal in the wireless charger base left and right center position, you can achieve wireless charging, the indicator light will have a breathing effect, 5 seconds after the extinguish, plug and play, convenient and quick.
2, first, open the "Settings", enter the "Battery and performance", look for the "Wireless charging" option. If you see it, it means that your Mi 11 has wireless charging superpowers! Choose Qi standard charger Secondly, choose a wireless charger that is in line with Qi standard. Mi 11 is compatible with many brands of Qi chargers, not only can you choose the official Xiaomi model, but also explore more brand options.
3, what to do after finding? Students are concerned about the use of wireless charging of mobile phones, and they need to buy a wireless charging base or wireless charging rear shell to use it. Connect the charging base Connect the charger to the wireless charging base,Then place the phone or a phone with a wireless charging back case on the wireless charging base.
4, HONOR 100pro wireless charging How to use I think HONOR 100pro wireless charging can be used like this: on a smooth plane. Place the phone on the charging area. Make sure the phone is in contact with the wireless charger. Plug the charger into the socket.
5. If your Huawei mobile phone supports wireless charging, place the mobile phone screen facing up in the center of the charger or the position suggested by the manufacturer after the wireless charger is powered.
6, the wireless charger is correctUsage: Connect the charger to the power supply. Please use the charging head, charging cable and wireless charging base purchased by yourself. Place the charger on a horizontal surface or other location suggested by the manufacturer. Place the phone on the charger with the screen facing up. For best performance, place the phone in the center of the charger or in the location recommended by the manufacturer.
1. The use of the HONOR Magic5 wireless charging method is as follows: Place the HONOR Magic5 mobile phone on the wireless charging board, and ensure that noThe cable charging board is powered on. Place the HONOR Magic5 phone on the wireless charging pad, and align the wireless charging coil on the back of the phone with the center of the wireless charging pad. When the mobile phone is placed on the wireless charging board, the wireless charging coil on the back of the mobile phone will automatically align with the center of the wireless charging board to achieve wireless charging.
2, use the wireless charging board, put the phone directly on the charging board, light up the blue light indicates that it is charging. Wireless charging allows you to charge your phone without using any plugs or wires. At present, many mobile phone brands have launched the concept of wireless charging, and BMW has also launched it out of a sensitive sense of smellCar wireless charging function.
3, first of all, you need to ensure that your mobile phone is supporting wireless charging, because wireless charging requires the hardware support of the mobile phone built-in wireless induction coil. Connect the wireless charging board with the data cable to the charger, and the general mobile phone charger can be used; Generally, after the charging board is connected, there will be a light reminder, and then put the phone on the charging board.
4, wireless charger usage: the mobile phone standard charger and data cable connected to the wireless charger, and then the mobile phone is/horizontally placed in the center position of the wireless charger base, wireless charging can be achieved, the indicator light will be calledSuction effect, extinguished after 5 seconds, plug and play, convenient and quick.
About wireless charging how to connect the circuit board and wireless charger circuit diagram this is the end of the introduction, do not know you find the information you need? If you want to know more about this, remember to follow this site. < / p >